Engine Components

Feuling Rocker Shaft Kit Complete Custom tooling was created to provide a countersink relief for the bolt/nut head versus machining away the entire end of the shaft per the factory design, Recommended for all M-Eight engines and especially for engines running higher lift camshafts and heavier valve spring pressures, Over double the strength of factory rocker shafts, Gas nitrated and final surface treated, Precision ground from 4140HT steel, Designed with strength in mind, Made in the USA

Feuling OE+ Camplate Milwaukee 8 Feuling OE+ stock replacement billet cam plates are manufactured from 6061 aluminum, providing increased rigidity and machined to Feuling? high tolerance standards, Direct bolt-in replacement and accept the factory or Feuling? OE+ oil pumps, Blue printed and matched oil passages to the engine case passages, kidney shapes are designed to maximize flow, Optimizes oil flow to and from the oil pump and in and out of the engine, aiding in reducing oil and engine temps, Tighter cam journal bore tolerance for improved cam fitment, Added Cam journal oil groove for cold start up protection and increased cam journal lubrication, Added oil pressure feed holes to front and back of cam journal to prevent excessive thrusting wear, For use with the factory or Feuling? OE+ oil pump, Made in the USA, For gear or chain drive cams (block-off plate PART #0932-0036 required when using gear drive cams).

Jims Tappet Cover Kit Milwaukee 8 Made from 6061 billet aluminum, Covers were designed to be installed with Twin Cam pushrod covers, they will not work with standard M-Eight pushrod covers, JIMS tappet covers have a sleek new look and are 1/2* lower than stock, making pushrod adjustment easy to do, Tappet covers with billet pushrod covers are available for the ultimate train cover upgrade (PART #s 0940-2012 and 0940-2013), Includes tappet covers, smooth billet pushrod cover and all necessary gaskets, O-rings and screws, Made in the U.S.A.

JE Piston Kits Machined from 2618-T6 high-tensile forged aluminum, Dome/dish features smooth flowing radii; requires no deburring or preparation, JE designs are specifically engineered for extreme applications including professional competition, Pins, pin, locks and rings included, Made in the U.S.A

Eastern Motorcycle Parts Right Pinion Bearing 24623-99B - Right Pinion Bearing - Made in the U.S.A.

Kibblewhite Wrist Pin Bushing - Twin Cam Constructed of SAE660 bearing bronze, Made in the U.S.A., Does not include oil holes. These must be drilled after installation.

Drag Specialities Cam Chain Tensioner Stock replacement hydraulic cam chain tensioners, Sold as a primary/secondary 2-piece kit

Oil Pressure Sensor Accurate reproductions of the OEM sending units, Precision calibrated

Figurati Designs Oil Dipstick Magnetic dipstick extends the lifespan of your bike by catching the loose metal filaments that naturally build up inside the oil pan, Simply replace your current dipstick with our magnetic dipstick to begin collecting any unwanted metal shards floating around in your oil supply, Made from jewelry-grade 316L stainless-steel, magnet, and plastic, Anti-fingerprint technology, High-visibility yellow , Powerful 2000 gauss neodymium magnet, 316L marine-grade stainless steel

 Cycle-Rama Harley-Davidson Camshafts 14-time Brute Horsepower Shoot-Out winner Cycle-Rama's line of cams are designed especially for 2007 and later Twin Cam & Milwaukee Eight engines, Cycle-Rama cams utilize specially designed proprietary ramps to increase flow velocity and maximize cylinder fill. As a result, they provide excellent low and mid-range performance with no compromise at high rpm.

Cycle-Rama CR50 Lifter Guides Anodized,  Billet , 6061 Aluminum Tappet Guides. They offer more stability to handle your performance camshaft. These are direct replacement for the stock plastic ones that can fail in your new build.

Feuling Parts Hydraulic Tensioner Kit Install or replace hydraulic camchain tensioners on stock M8 models, Kit includes out chain, outer crank 17 tooth crank sprocket, replacement camchain pad and pin, and spacer kit, Made in the USA, Works with a combination of factory, SE or S&S oiling systems., Camshaft sprocket spacing alignment/thrust washer kit 0925-0951 will not fit '23-'24 models with 121" VVT motor.

Feuling Parts Cam ChainTensioner Pad  Injection molded nylon with PTFE (polytetrafluoroethylene) added to increase wear and friction resistance, Includes chain tensioner pad and pin, Works with the factory aluminum housing and hydraulic unit, Made in the USA